Asian Fan Placemat

Deprecated: wp_make_content_images_responsive is deprecated since version 5.5.0! Use wp_filter_content_tags() instead. in /home/sewing/dev.sewing.org/wp-includes/functions.php on line 4779

Asian fan placemat embroidery project from Singer @ www.singerco.comWith the use of embroidery and decorative stitches, create this Asian-inspired placemat that will enhance any table setting. Finished size is 15” x 20”.

Materials

½ yard of 45” cotton or other suitable fabric for each placemat
½ yard low loft batting for each placemat
2½ yards of 1/8” ribbon for each placemat
Water-soluble or chalk marker
Temporary spray adhesive
Quilter’s rule
Large tapestry needle
Thread:
Black all-purpose thread
Robison-Anton® polyester – Red #5563
Fancy Fan Embroidery Design

These project instructions are specific to a Singer sewing machine; however, the project can be adapted for use on other machines.

Equipment

QUANTUM® XL-5000 & Professional Sew Ware™ 2.00a Software
Important Note: These project instructions are specific to the Singer QUANTUM® XL-5000 embroidery machine; however, the project can be adapted for use on other machines.

Instructions

1. Cut two pieces of background fabric 16” x 21”.
2. Cut one piece of batting 16” x 21”.
3. Using a water-soluble or chalk marker, mark the center of one piece of background fabric in both directions.
4. Secure batting to wrong side of fabric with a temporary spray adhesive.
5. Hoop fabric and batting.

At the Computer

(The sample in the photo shows the design slightly enlarged. Follow the directions below for modifying the design as shown in the sample, if desired.)

1. Open the PSW 2.00a software and insert the smart media card into the correct slot.
2. From the Main Menu, click on Open.
3. The Open Design dialog box appears. Click the down arrow to the right of the drive box, then click on the drive that contains the Asian Fan design.
4. Click on the Asian Fan file.
5. Click OK.
6. In the Open Image dialog box, click on Cancel. The design is now on the screen.
7. From the Main menu, click on Modify; click on Dimensions.
8. When the Dimensions dialog box opens, type 5.00 in the X-axis box. (This will automatically change the y dimension to. 3.88.)
9. Type 90 in the Rotation Box.
10. Click OK.
11. From the Main Menu, click on File; click on Write to Converter.
12. When the Save Design dialog box opens, click on the Smart Media icon.
13. Click on Save in New Page.

At the Machine

1. Attach the embroidery foot.
2. Install the embroidery unit making sure that the machine is off.
3. Insert the smart media card into the Quantum XL-5000.
4. Turn the machine on.
5. Touch the Introductory Screen.
6. Touch OK to allow the carriage to move into the starting position.
7. Touch Smart Media icon on the lower right of the screen.
8. Touch Fan design.
9. Touch Enter key.
10. Touch Editing Box. Use Positioning Arrows to center the hoop.
11. Touch the Return Arrow.
12. Touch OK.
13. Lower the presser foot and touch the green light to stitch the embroidery design.

Sewing Procedure

1. Pin embroidered piece to second piece of background fabric, right sides together.
2. Use a ½ “ seam allowance; stitch around all edges leaving an opening large enough to turn the placemat right side out.
3. Trim excess batting from seam allowance and trim corners at an angle.
4. Turn placemat right side out.
5. Press.
6. Hand stitch opening closed.
7. With a water-soluble or chalk marker, draw a guide-line 2” from each edge.
8. Thread needle and bobbin with black all-purpose thread.
9. Select Pink Folder 1; row 2; third stitch from left. Engage 2X.
10. Place the left side of presser foot ”I” on the drawn line and stitch a row of decorative stitches on all four sides of placemat.
11. Weave ribbon through the line of decorative stitching with a large tapestry needle.
12. Fold under the edges of the ribbon and stitch the ends of the ribbon at the edge of placemat to secure them in place.

6/06